产品尺寸图

※特点：
1、 BMB-10采用军工级电位器及精密电阻,高精度、低温漂,调信号；外壳为304不锈钢，更强的EMC防护性能，抗干扰能力强; 盒内有10个四线制带屏蔽线的传感器接入端，一个六线制的输出端。输出端的信号为所有接入传感器的集成信号输出。
2、采用专用密封接头；
3、补偿调节采用高稳定性的多圈电位器；
4、盖板有防水橡胶垫圈，防水，防尘，适用于环境条件恶劣的工业 环境；
5、每一个接线位有独立的可调电位器，通过调整精密电位器的阻值，补偿和修正四角偏差；
6、用于各种工业称重应用，包括地磅、料罐秤、料仓及传送带秤等设备，广泛应用于养殖、搅拌站、基建、化工等行业。
※FEATURES:
1. The BMB-10 utilizes military-grade potentiometers and precision resistors, featuring high accuracy, low temperature drift, and precise signal adjustment. Its enclosure is constructed from 304 stainless steel, providing enhanced EMC protection and strong anti-interference capability. The unit is equipped with 10 four-wire shielded sensor input terminals and one six-wire output terminal. The output signal is the integrated signal from all connected sensors.
2. Equipped with dedicated sealed connectors;
3. High-stability multi-turn potentiometers are used for compensation adjustment;
4. The cover plate is fitted with a waterproof rubber gasket, providing water and dust resistance, and is suitable for harsh industrial environments;
5. Each wiring position is equipped with an independent adjustable potentiometer; by adjusting the resistance of the precision potentiometer, the four-corner deviation can be compensated and corrected;
6. Suitable for various industrial weighing applications, including truck scales, tank scales, silo scales, and conveyor scales, and widely used in industries such as breeding, mixing stations, infrastructure, and chemical engineering.
※使用说明：
本接线盒适用于模拟传感器的连接，各接线端子标示如下:
EX+:传感器的供桥电源正端
SIG-:传感器的输出信号负端
EX-:传感器的供桥电源负端
SHLD:屏蔽电缆的屏蔽层
SIG+:传感器的输出信号正端
(使用六线制传感器时，需将电源正与感应正短接至EX+;电源负与感应负短接至EX-。)接线盒调整方法: 电位器R1-R10可分别微调各路传感器的输出信号，用于系统四角调整。顺时针增加，逆时针减少重量。
※User Manual:
This junction box is suitable for the connection of analog sensors;The marking of each terminal is as follows:
EX+: Positive terminal of the sensor’s bridge power supply；
SIG-: Negative terminal of the sensor’s output signal；
EX-: Negative terminal of the sensor’s bridge power supply；
SHLD: Shielding layer of the shielded cable；
SIG+: Positive terminal of the sensor’s output signal；
(When using a 6-wire sensor, short-circuit the positive power supply terminal and the positive sensing terminal, then connect them to EX+; short-circuit the negative power supplyterminal and the negative sensing terminal, then connect them to EX-.) Junction Box Adjustment Method：Potentiometers R1-R10 can individually fine-tune the output signal of each sensor, which is used for system four-corner adjustment. Turning clockwise increases the weight reading, while turning counterclockwise decreases it.

产品技术特性表